Stainless Steel Wire Balustrades

Stainless Steel Wire Balustrades :: Stainless Steel Posts Stainless Steel Hand Rails :: Stainless Steel Wire Wire Balustrade IF YOU HAVE ANY QUESTIONS ON YOUR WIRE BALUSTRADE, PLEASE CONTACT US ON 01628 526995. DUE TO THE LARGE POSSIBLE VARIATIONS AND SIZES, THIS PRODUCT RANGE IS NOT AVAILABLE TO BE PURCHASED DIRECTLY FROM THIS SITE. PLEASE SEND YOUR REQUIREMENTS TO US BY EMAIL (htfenceanddecking@btconnect.com) OR FAX (01628 522541) OR TEL (01628 526995). PAYMENT WILL BE TAKEN BY CREDIT CARD. Stainless Steel Wire Balustrades with Windsor range of Stainless Steel Posts Posts and fittings are available in either Grade 304 (standard) or Marine Grade (316). Marine Grade should be used within 5 miles of the sea or around swimming pools. The stainless steel posts and rails are available in either a 42.4mm diameter or 48.3mm. The 42.4mm diameter posts are most suitable for balustrading with a total length under 15 metres. Larger decks should use posts and rails with a 48.3mm diameter. This is recommended both for strength and appearance. The Stainless Steel Wire must be connected in straight lines. The wire can pass through intermediate newel posts. The wire is joined to the newel posts by an End Fixing Unit. The End Fixing Unit consists of a Dome Head Stud Terminal, a lock nut and a Threaded Terminal which is clamped (swaged) onto the wire. A Tensioner is required if the wire length exceeds 4 metres. Two tensioners are required if the wire length exceeds 15 metres. The maximum length is 25m for a single run. The Tensioner will replace the End Fixing Unit. See our Step by Step Stainless Steel Wire with Stainless Steel Posts Assembly Instructions for straight runs. The Stainless Steel Wire Balustrade with WINDSOR Stainless Steel Posts is only available on level decking. ORDERING WIRE AND STAINLESS STEEL POSTS Please let us know your stainless steel requirements. A sketch of your balustrading requirements would be very useful. You may place your order by email, fax or telephone (see top of page). In order to make the correct lengths of wire, we will need your requirements for each section. Please go to the Contacts box (at the top of this page) and request a 'Wire with Stainless Steel Posts Measurement Form', which will be as set out below. We will not treat this as a firm order until you tell us that it is. Section * No. of wires per section Distance between centres of external posts (mm.) End fixing units Tensioner units per wire 1 . . . . 2 . . . . 3 . . . . 4 . . . .

* Each straight wire length is a Section. For each Section we need the Distance between centres of external posts to calculate the wire length.

Height from deck to top of handrail

mm.

We will assume that wires are spread evenly over the post, unless you tell us to the contrary.

Stainless Steel Posts and Handrail Units for Windsor Balustrades

Satin Stainless Steel Upright Post welded onto base plate 120mm diameter. Diameter 42.4mm and 48.3mm, Height 1000mm. Drilled for glass clamps. 304 Grade  42.4mm - £96.14 inc. VAT 48.3mm - £103.79 inc. VAT 316 Marine Grade 42.4mm - £120.18 inc. VAT 48.3mm - £124.55 inc. VAT	Satin Stainless Steel Cover Plate over Base Plate. Diameter 120mm. 304 Grade - £10.38 inc. VAT 316 Marine Grade - £13.44 inc. VAT
Satin Stainless Right Angle Elbow. Diameter 42.2mm. To turn a stainless steel rail through a 90 degree angle. 304 Grade - £22.40 inc. VAT 316 Marine Grade - £28.96 inc. VAT	Satin Stainless Steel Tube. Diameter 42.44mm. Standard length 6000mm. Free cut to length. 304 Grade - £30.15 inc. VAT per metre 316 Marine Grade - £52.34 inc. VAT per metre
Satin Stainless Steel Corner Saddle Stem. For use with Iroko Hardwood Handrail (below). 304 Grade - £15.30 inc. VAT 316 Marine Grade - £16.39 inc. VAT	Satin Stainless Steel Straight Saddle Stem. Glued on to post. For use with Iroko Hardwood Handrail (below). 304 Grade - £15.30 inc. VAT 316 Marine Grade - £16.39 inc. VAT
Iroko Hardwood Handrail with 4 alternative ends. a) Dowelled and pegged for connecting to another handrail. b) Flat end to fit into stainless steel wall socket. c) Dome End. d) Mitred at 45 degrees to right angle. Diameter 42.4mm. Length 1800mm. £58.75 inc. VAT	Satin Stainless Steel End Cap. Diameter 42.4mm. 304 Grade - £7.65 inc. VAT 316 Marine Grade - £7.65 inc. VAT
Satin Stainless Steel Tube Connector. Diameter 42.2mm.  304 Grade - £9.83 inc. VAT 316 Marine Grade - £12.13 inc. VAT	Universal Fitting for attaching stainless steel rails to post. 304 Grade - £9.83 inc. VAT 316 Marine Grade - £13.33 inc. VAT
Satin Stainless Steel Wall Socket. Diameter 42.2mm. 304 Grade - £18.03 inc. VAT 316 Marine Grade - £20.76 inc. VAT	Satin Stainless Steel Elbow. Diameter 42.4mm. For finishing a stainless steel rail at the post. 304 Grade - £19.12 inc. VAT 316 Marine Grade - £24.59 inc. VAT
Tube of glue for Stainless Steel £14.10 inc. VAT	Stainless Steel Cleaner £21.15 inc. VAT

Stainless Steel Marine Grade Wire and Fixings for Windsor balustrades

Satin Stainless Steel End Fixing Unit £16.99 inc. VAT	Satin Stainless Steel Tensioner Unit £30.18 inc. VAT
Marine Grade Stainless Steel 4mm 1x19 Wire £1.73 inc. VAT per metre	.

 Decking-Fencing-Accessories.co.uk for all your Stainless steel wire balustrade needs